Electromotive Store Powered by E-Ticket MotorsportsElectromotive TecM Info PageElectromotive TecGT Information PageElectromotive Tec3r Info PageElectromotive Parts Store
Home > Electromotive Store > Electromotive ECU > Electromotive TecM
View Cart

Electromotive TecM Standalone ECU

Introducing an E-Ticket Motorsports exclusive product, the Electromotive TecM.

The first true "Plug and Play", fully tunable standalone ECU for BMW ODB1 6-cylinder engines.

With all the features found in other Electromotive products the Electromotive TecM is a powerful solution for highly modified engines whether normally aspirated or forced induction.

- Electromotive TecM ECU
- Serial Cable
- Electromotive WinTEC4 Software
- Ground Protection Strap
Electromotive TecM ECU

E-Store Pricing:              Add to Cart
Electromotive ECU's

Electromotive TecM

Electromotive TecGT

Electromotive Tec3r

Electromotive Tec S

Electromotive Parts

Wiring Harnesses




Technical Details (For Answers to commonly asked questions check out the FAQ Page)

Electromotive TECm is a replacement motherboard for the Motronic ECU that controls many mid 90’s BMW’s. The TECm is not an aftermarket ECU with an adapter. It is a custom built motherboard designed specifically as a direct replacement for your Bosch Motronic motherboard with built in support for BMW specific features such as VANOS and A/C control. Electromotive TECm can even be installed so that it leaves no outward sign of its presence. All interfaces to your car are supported. Plug in a Electromotive TECm and the factory tach, CEL and fuel consumption gauge all work and the reliable factory engine harness stays intact. You get the advantages of a modern race ECU without the lost time and expense engineering and building a custom harness or changing sensors.

The Electromotive TECm replaces Motronic ‘413’ and ‘506’ ECU’s, including EWS units. They are common on BMW M50 (E36 325, E34 525) or S50 (E36 M3) engines and are often used in the popular ODB2 (M52, S52) to ODB1 intake and harness performance upgrade.

Who can use a Electromotive TECm? If you race in a series where you must manage different tunes for classification purposes (e.g. NASA GTS) the Electromotive TECm is your ticket. Maybe you plan to build or already have a forced induction engine and need to take control of it. Or maybe you are one of those performance minded people who makes incremental changes and wants a platform that will grow with you. The Electromotive TECm is an easy to implement solution for these projects and more.

· Direct bolt in replacement of Motronic ‘413’ and ‘506’ ECU’s motherboard, including EWS units
· VANOS (Cam) Control based on RPM and throttle position
· Full - Sequential Injection
· Idle Air Controller (IAC) Support Built In
· MAF air flow meter Support
· Factory A/C control including WOT compressor disconnect

TECm is based on the Electromotive TecGT Race ECU and uses the same easy to use Windows based WinTEC4 software. Because of this it inherits the patented, multiprocessor, high resolution Ignition that Electromotive is famous for as well as most of the features of the Electromotive TecGT.

· 16x16 Fuel and Timing Maps
· Coolant Temperature Based Ignition and Fuel Compensations
· Intake Air Temperature Based Ignition and Fuel Compensations
· EGO (O2 Sensor) Target Tables with Closed Loop Control
· Automatic VE tool built into software (learns fuel map on the fly)
· Hi and Low Impedance Injector Drivers Built In
· MAF and MAP Sensor Support (up to 7 bar)
· Warm-Up Enrichments
· Over Boost Fuel Cut
· 3 Rev Limiters
· Idle Control
· Fuel and Timing Trim by Cylinder
· Onboard Data Recording
· CAN Bus support to feed external data loggers (AIM MXL, XG Log, DL1, DL2)

Unused pins in the OEM Motronic are exploited in the Electromotive TECm to create two general purpose inputs (GPI) and one general purpose output (GPO). They allow for additional advanced features to be built in such as:

· Boost Control (when using the MAP feature)
· Nitrous Control (RPM and Load Enable Nitrous)
· Nitrous Retard (Multiple Stage Timing Retard)
· Auxiliary Fuel Pump Control
· Fan Thermo Control
· Intake Runner Control
· Custom Controls Based on RPM and Load
· Shift Light
· Valet Switch
· Onboard Data Recording
· Timed Advance
· Timed Power Cut (no lift shift)
· Fuel Trim
· Advance Trim

To better understand the WinTEC4 software used to configure a TECm you can download it here.
E-Specials - Sign up for great offers and dealsBuy Electromotive Products OnlineElectromotive & E-Ticket Motorsports Company Info

SiteMap Racing ECU Site Standalone Engine Management site All Rights Reserved. Copyright E -Ticket Motorsports 2020. Web Design by Intellisign